IPP> Proposed update to PWG IEEE-ISTO 5100.1 "finishings" extensi on, version 0.1, 10/30/02

IPP> Proposed update to PWG IEEE-ISTO 5100.1 "finishings" extensi on, version 0.1, 10/30/02

IPP> Proposed update to PWG IEEE-ISTO 5100.1 "finishings" extensi on, version 0.1, 10/30/02

Fullman, Don fullman at cp10.es.xerox.com
Thu Oct 31 15:26:55 EST 2002


I've posted a Proposed update to the PWG IEEE-ISTO 5100.1 "finishings"
extension, version 0.1, 10/30/02.  Its available at:

The latest version of the update is located at the fixed URL:

ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-latest.pdf
ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-latest.doc 

The version with the version number and date in the file name is the same as
the latest and is at:
ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-v01-021030.pdf 
ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-v01-021030.doc 

The version with change tracking from the 5100.1-2001 is at:
ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-v01-021030-rev.pdf 
ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-v01-021030-rev.doc 

Here is the change log which will be published with the standard after it is
approved by a PWG IPP WG Last Call, just as for the original standard to
move it from Proposed Standard to Draft Standard:

The following changes have been made to IEEE-ISTO  5100.1-2001, February 5,
2001 to make the updated IEEE-ISTO 5100.1-2002:
	1.	Added the following generic enum values:  'fold', 'trim',
'bale', 'booklet-maker', 'jog-offset'.
	2.	Added the following more specific enum values:  'bind-left',
'bind-top', 'bind-right', 'bind-bottom', 'punch-2-hole', 'punch-3-hole',
'punch-4-hole', 'booklet-fold-staple', 'booklet-fold',
'fold-c-short-in-thirds-sheet', 'fold-z-short-in-thirds-sheet',
'fold-z-short-sheet'.
	3.	Added a semantic description for the use of multiple values
with the "finishings" Job Template Job attribute.
	4.	Added a semantic description for an additional coordinate
system that is relative to the document's orientation, and added the
following enum values that used this new coordinate system:
'staple-top-left-rel', 'staple-bottom-left-rel', 'staple-top-right-rel',
'staple-bottom-right-rel', 'edge-stitch-left-rel', 'edge-stitch-top-rel',
'edge-stitch-right-rel', 'edge-stitch-bottom-rel', 'staple-dual-left-rel',
'staple-dual-top-rel', 'staple-dual-right-rel' and 'staple-dual-bottom-rel'.
	5.	Corrected the IANA Registrations.

We also put it in the IEEE-ISTO format that Ron Bergman worked out with the
IEEE-ISTO.

Send comments to the ipp at pwg.org DL.

Thanks,
Tom Hastings and Don Fullman



More information about the Ipp mailing list