[IPP] First draft of IPP Finishings 2.1 available for review

[IPP] First draft of IPP Finishings 2.1 available for review

[IPP] First draft of IPP Finishings 2.1 available for review

Michael Sweet msweet at apple.com
Thu Apr 14 20:58:27 UTC 2016


Smith,

I think we want to include the finishings registrations in the latest standard document.


> On Apr 14, 2016, at 4:55 PM, Kennedy, Smith (Wireless Architect) <smith.kennedy at hp.com> wrote:
> 
> I wasn't sure whether the registrations posted earlier to the reflector were sufficient or if they needed to be included.  I will make these changes in the next draft, to be posted hopefully by EOD tomorrow, in preparation for the F2F.
> 
> Smith
> 
> 
> 
>> On 2016-04-14, at 2:32 PM, Michael Sweet <msweet at apple.com <mailto:msweet at apple.com>> wrote:
>> 
>> Bill,
>> 
>>> On Apr 14, 2016, at 4:06 PM, wamwagner at comcast.net <mailto:wamwagner at comcast.net> wrote:
>>> 
>>> Hi Smith,
>>> My notes indicated that EcoStaple (perhaps as “crimp”) and Engineering Z Fold values would be  included in Finishings 2.1, but I do not see them. Am I just missing tem or was there a change of approach?
>> 
>> Yes, I think these should be in there but currently are not.
>> 
>> The changes that are needed are:
>> 
>> 1. Figure 1: Add 'fold-engineering-z' (I owe you this one Smith)
>> 
>> 2. New Section 5.1.x PWG 5100.1-YYYY "finishings Values"
>> 
>>    - New "finishings" enum value 101 with keyword name 'fold-engineering-z'
>>    - "Fold the hardcopy output vertically into three sections, forming a Z but leaving room for binding, punching, or stapling along the top edge."
>> 
>> 3. Section 5.2.6.4 “folding” Examples
>> 
>>    `fold-engineering-z’
>>    folding = { folding-direction=’inward’ folding-offset=11593
>>                folding-reference-edge=’top’ },
>>              { folding-direction=’outward’ folding-offset=20646
>>                folding-reference-edge=’top’ }
>> 
>> 4. New Section 5.2.12.5 stitching-type (type2 keyword)
>> 
>>    The "stitching-type" member attribute specifies the type of stitching to use. The following values are defined by this specification:
>> 
>>        'auto': Automatically choose a stitching type based on the Set being finished.
>>        'crimp': Crimp the Set together.
>>        'wire': Use wire staples.
>> 
>> 5. New Section 6.x stitching-type-supported (1setOf type2 keyword)
>> 
>>    The "stitching-type-supported" Printer attribute lists the supported values for the "stitching-type" (section 5.2.12.5) member attribute.
>> 
>> 
>> Note: JDF has a "stitching type" with values "corner", "saddle", and "side".  Perhaps we should use the name "stitching-kind" instead to avoid confusion (since JDF doesn't currently support crimping/eco-staples)???
>> 
>> _________________________________________________________
>> Michael Sweet, Senior Printing System Engineer
>> 
> 

_________________________________________________________
Michael Sweet, Senior Printing System Engineer

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.pwg.org/pipermail/ipp/attachments/20160414/d286dc3d/attachment.html>


More information about the ipp mailing list