I'll add that as well.
Cheers,
Smith
---
Smith Kennedy
Wireless Architect - Client Software - IPG-PPS
Standards - PWG / Bluetooth SIG / Wi-Fi Alliance / NFC Forum
PWG Chair
HP Inc.
> On Apr 14, 2016, at 6:13 PM, Yardumian, Rick <RYardumian at ciis.canon.com> wrote:
>> Hi Smith, Mike & Bill,
>> For completeness should we add the new ‘draw-line’ value to trimming-type in Finishing 2.1?
>> Thanks,
> Rick
>> From: ipp [mailto:ipp-bounces at pwg.org] On Behalf Of Kennedy, Smith (Wireless Architect)
> Sent: Thursday, April 14, 2016 1:56 PM
> To: Michael Sweet
> Cc: ipp at pwg.org> Subject: Re: [IPP] First draft of IPP Finishings 2.1 available for review
>> I wasn't sure whether the registrations posted earlier to the reflector were sufficient or if they needed to be included. I will make these changes in the next draft, to be posted hopefully by EOD tomorrow, in preparation for the F2F.
>> Smith
>>>> On 2016-04-14, at 2:32 PM, Michael Sweet <msweet at apple.com> wrote:
>> Bill,
>> On Apr 14, 2016, at 4:06 PM, wamwagner at comcast.net wrote:
>> Hi Smith,
> My notes indicated that EcoStaple (perhaps as “crimp”) and Engineering Z Fold values would be included in Finishings 2.1, but I do not see them. Am I just missing tem or was there a change of approach?
>> Yes, I think these should be in there but currently are not.
>> The changes that are needed are:
>> 1. Figure 1: Add 'fold-engineering-z' (I owe you this one Smith)
>> 2. New Section 5.1.x PWG 5100.1-YYYY "finishings Values"
>> - New "finishings" enum value 101 with keyword name 'fold-engineering-z'
> - "Fold the hardcopy output vertically into three sections, forming a Z but leaving room for binding, punching, or stapling along the top edge."
>> 3. Section 5.2.6.4 “folding” Examples
>> `fold-engineering-z’
> folding = { folding-direction=’inward’ folding-offset=11593
> folding-reference-edge=’top’ },
> { folding-direction=’outward’ folding-offset=20646
> folding-reference-edge=’top’ }
>> 4. New Section 5.2.12.5 stitching-type (type2 keyword)
>> The "stitching-type" member attribute specifies the type of stitching to use. The following values are defined by this specification:
>> 'auto': Automatically choose a stitching type based on the Set being finished.
> 'crimp': Crimp the Set together.
> 'wire': Use wire staples.
>> 5. New Section 6.x stitching-type-supported (1setOf type2 keyword)
>> The "stitching-type-supported" Printer attribute lists the supported values for the "stitching-type" (section 5.2.12.5) member attribute.
>>> Note: JDF has a "stitching type" with values "corner", "saddle", and "side". Perhaps we should use the name "stitching-kind" instead to avoid confusion (since JDF doesn't currently support crimping/eco-staples)???
>> _________________________________________________________
> Michael Sweet, Senior Printing System Engineer
>>-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.pwg.org/pipermail/ipp/attachments/20160415/5b1e74dd/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/pkcs7-signature
Size: 3319 bytes
Desc: not available
URL: <http://www.pwg.org/pipermail/ipp/attachments/20160415/5b1e74dd/attachment.p7s>