IPP Mail Archive: IPP> Proposed update to PWG IEEE-ISTO 5100

IPP> Proposed update to PWG IEEE-ISTO 5100.1 "finishings" extensi on, version 0.1, 10/30/02

From: Fullman, Don (fullman@cp10.es.xerox.com)
Date: Thu Oct 31 2002 - 15:26:55 EST

  • Next message: McDonald, Ira: "RE: IPP> Proposed update to PWG IEEE-ISTO 5100.1 "finishings" ext ensi on, version 0.1, 10/30/02"

    I've posted a Proposed update to the PWG IEEE-ISTO 5100.1 "finishings"
    extension, version 0.1, 10/30/02. Its available at:

    The latest version of the update is located at the fixed URL:

    ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-latest.pdf
    ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-latest.doc

    The version with the version number and date in the file name is the same as
    the latest and is at:
    ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-v01-021030.pdf
    ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-v01-021030.doc

    The version with change tracking from the 5100.1-2001 is at:
    ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-v01-021030-rev.pdf
    ftp://ftp.pwg.org/pub/pwg/ipp/new_VAL/pwg-ipp-finishings-v01-021030-rev.doc

    Here is the change log which will be published with the standard after it is
    approved by a PWG IPP WG Last Call, just as for the original standard to
    move it from Proposed Standard to Draft Standard:

    The following changes have been made to IEEE-ISTO 5100.1-2001, February 5,
    2001 to make the updated IEEE-ISTO 5100.1-2002:
            1. Added the following generic enum values: 'fold', 'trim',
    'bale', 'booklet-maker', 'jog-offset'.
            2. Added the following more specific enum values: 'bind-left',
    'bind-top', 'bind-right', 'bind-bottom', 'punch-2-hole', 'punch-3-hole',
    'punch-4-hole', 'booklet-fold-staple', 'booklet-fold',
    'fold-c-short-in-thirds-sheet', 'fold-z-short-in-thirds-sheet',
    'fold-z-short-sheet'.
            3. Added a semantic description for the use of multiple values
    with the "finishings" Job Template Job attribute.
            4. Added a semantic description for an additional coordinate
    system that is relative to the document's orientation, and added the
    following enum values that used this new coordinate system:
    'staple-top-left-rel', 'staple-bottom-left-rel', 'staple-top-right-rel',
    'staple-bottom-right-rel', 'edge-stitch-left-rel', 'edge-stitch-top-rel',
    'edge-stitch-right-rel', 'edge-stitch-bottom-rel', 'staple-dual-left-rel',
    'staple-dual-top-rel', 'staple-dual-right-rel' and 'staple-dual-bottom-rel'.
            5. Corrected the IANA Registrations.

    We also put it in the IEEE-ISTO format that Ron Bergman worked out with the
    IEEE-ISTO.

    Send comments to the ipp@pwg.org DL.

    Thanks,
    Tom Hastings and Don Fullman

    This archive was generated by hypermail 2b29 : Thu Oct 31 2002 - 15:27:36 EST